esp32-rf.yaml

---
## TODO
#
# Hardware
#   - Broche n°2 = GND ==> n'est pas reliée à GND
#   - 4.7K pull-up entre GPIO13 et 3.3V
#
# Software
#   - configurer DS18B20 sur GPIO13
#   - configurer résistance lum. sur GPIO34
#   - tester RXB6 une fois connecté
#   - tester TX1 une fois connecté
#   - tester DS18B20 une fois connecté
#   - tester résistance lum. une fois connectée
#
# Schéma
#   - IC ESP32 : broche 2 n'est pas GND
#   - inverser polarité buzzer
#   - connecter buzzer sur gpio16 et GND
#   - led sur gpio0
#   - data de DS18B20 sur GPIO13 (car S02 sur flash interne)
#   - 4.7K pull-up entre GPIO13 et 3.3V
#   - alim +5V du RXB6 sur +3.3V pour ne pas avoir DATA en >3.3V
#   - écarter BME280 et TX 433

substitutions:
  devicename: esp32-rf
  upper_devicename: ESP32 RF
  rf433_tx_pin: GPIO23
  rf433_rx_pin: GPIO32
  bme280_i2c_sda: GPIO18
  bme280_i2c_scl: GPIO19
  buzzer_pwm: GPIO16
  buzzer_platform: ledc

packages:
  device_base: !include common/device_base.yaml
  device_esp32: !include common/device_esp32.yaml
  rf433: !include common/rf433.yaml
  bme280: !include common/bme280.yaml
  buzzer: !include common/buzzer.yaml

esphome:
  name_add_mac_suffix: true

esp32:
  board: nodemcu-32s

wifi:
  manual_ip:
    # pour une connection rapide, et pour que le conteneur docker esphome puisse trouver l'ESP sans mDNS
    static_ip: 192.168.1.244
    gateway: 192.168.1.1
    subnet: 255.255.255.0

## Device-specific

number:
  - platform: template
    id: luminosity_max_value
    name: valeur RAW de la luminosité au max
    restore_value: yes
    initial_value: 2
    optimistic: yes
    min_value: 0
    max_value: 3.33
    step: 0.01
    on_value:
      then:
        - sensor.template.publish:
            id: linear_regression_a
            state: !lambda 'return (100.0 - 0.0) / ( x - id(luminosity_min_value).state);'
        - sensor.template.publish:
            id: linear_regression_b
            state: !lambda 'return 100.0 - ( id(linear_regression_a).state * x);'
  - platform: template
    id: luminosity_min_value
    name: valeur RAW de la luminosité au min
    restore_value: yes
    initial_value: 0.075
    optimistic: yes
    min_value: 0
    max_value: 3.33
    step: 0.001
    on_value:
      then:
        - sensor.template.publish:
            id: linear_regression_a
            state: !lambda 'return (100.0 - 0.0) / ( id(luminosity_max_value).state - x);'
        - sensor.template.publish:
            id: linear_regression_b
            state: !lambda 'return 100.0 - ( id(linear_regression_a).state * id(luminosity_max_value).state);'

one_wire:
  - pin: GPIO13
    platform: gpio

sensor:
  - platform: dallas_temp
    address: "0x6700044c9793ff28"
    name: "temperature 18b20"
  - platform: template
    id: linear_regression_a
    name: régression linéaire facteur
    accuracy_decimals: 2
    update_interval: never
  - platform: template
    id: linear_regression_b
    name: régression linéaire offset
    accuracy_decimals: 2
    update_interval: never
  - platform: adc
    pin: GPIO34
    attenuation: auto
    id: luminosity_raw_adc
    name: luminosity raw adc
    accuracy_decimals: 4
    update_interval: 60s
    on_raw_value:
      then:
        - sensor.template.publish:
            id: luminosity
            state: !lambda 'return x;'
  - platform: template
    id: luminosity
    name: luminosity
    unit_of_measurement: "%"
    accuracy_decimals: 0
    icon: mdi:brightness-percent
    state_class: measurement
    filters:
      - lambda: return x * id(linear_regression_a).state + id(linear_regression_b).state;

button:
  - platform: template
    name: "MAJ sensor lumiere"
    on_press:
      - component.update: luminosity_raw_adc
  - platform: template
    name: "Calibrage MAX luminosité"
    on_press:
    - number.set:
        id: luminosity_max_value
        value: !lambda 'return id(luminosity_raw_adc).state;'

output:
  - platform: ledc
    id: led_pin
    pin: GPIO0

light:
  - platform: monochromatic
    output: led_pin
    id: led
    name: "LED"
    gamma_correct: 0
    effects:
      - pulse
      - automation:
          name: Sleep pattern
          sequence:
            - light.turn_on:
                id: led
                brightness: 100%
                transition_length: 2s
            - delay: 2.5s
            - light.turn_on:
                id: led
                brightness: 1%
                transition_length: 4s
            - delay: 4.5s